Load-bearing wall removal
Opening a floor plan starts with an engineer deciding what the wall carries. Work begins only after the drawings are permitted.

Engineered, permitted and inspected
SW Florida Builders Group manages load-bearing wall removal in Southwest Florida under a licensed engineer’s design, with permits, beam installation and inspections handled for you.
Opening a floor plan starts with an engineer deciding what the wall carries. Work begins only after the drawings are permitted.
LVL, steel and other beams are sized by the engineer for the loads above. We install them to the drawing and have them inspected.
Openings that sag or are being widened need correctly sized headers. The engineer specifies the header and its support.
Beams must land on posts and connectors that carry the load down to the foundation. We build the full load path, not only the beam.
Supports hold the structure while permanent members are placed. Shoring is planned as part of the engineered scope.
Cracked, rotted or storm-damaged members are replaced under an engineer’s repair detail. Hidden work is inspected before it is covered.

A wall can look like a simple partition and still carry roof or floor loads. Only a licensed engineer can say what a wall carries, and in Florida the load path also has to resist wind uplift through roof-to-wall connections. That is why we do not guess, and why we do not offer advice on removing a wall without engineering.
The engineer reviews the house, sizes the beam and posts, and details the footings or connections below. Those sealed drawings go into the permit package. Homes with block walls, truss roofs or earlier additions each have different answers, so the design is specific to your house.
Wind matters here as well. A wall that stiffens the house against lateral forces cannot simply disappear, so the engineer checks whether the remaining structure still resists wind and, if not, adds the posts, connections or bracing needed to make up the difference.
A beam only works if the load has somewhere to go. Each end sits on a post or bearing wall, and that support continues down through connectors, framing and a footing or slab that can take the added point load. Engineers call this the continuous load path.
Beams can be engineered lumber such as LVL, steel or another material depending on span and load. Hardware matters too, because metal connectors tie members together against uplift and lateral forces, which the engineer accounts for in a high-wind state like Florida.
Ceilings, ductwork, plumbing and wiring often run through the area, and rerouting them is part of the scope. We list those items in the written price so they are not a surprise.


Illustrative photography of this type of work. These images are not records of specific completed SW Florida Builders Group projects.
Structural changes require a permit, and your city or county decides the submittal requirements. Most ask for sealed engineering, and some ask for a survey or other drawings.
Plan review is where many structural jobs slow down, usually because the drawings do not match the field conditions. We confirm dimensions and framing before submittal, which helps reduce, though never eliminate, review comments.
We cannot guarantee approval or a review timeline. Inspectors may check footings, framing, connectors and the beam installation before it is covered with finishes. If the work is part of a larger renovation in a mapped flood hazard area, the 50 percent rule may apply, comparing cost with the structure’s market value, excluding land. Local rules can be stricter.
| Scenario | What usually drives the permit | What to settle early |
|---|---|---|
| Opening between two rooms | Engineer’s beam and post design with the load path | What the wall carries above |
| Kitchen to living room | Beam sizing plus rerouting of services | Cabinet, wiring and plumbing locations |
| Widening a door or window | Header size and bearing at each side | Wall type and impact-rated opening needs |
| Replacing a sagging header | Engineer’s repair detail and support | Cause of the sag and any moisture source |
| Storm-damaged framing | Engineered repair and inspection of hidden work | Extent of damage and available documentation |
We look at the wall, the framing above and what runs through it.
A licensed engineer designs the beam, posts and supports for your house.
We submit the sealed drawings and handle review comments.
Temporary supports go in, permanent members are placed to the drawing and inspections are called.
Walls, ceilings and services are restored and the permit is closed.
We do not recommend or advise it. Whether a wall carries load is an engineering question, and structural changes require a permit and inspections in Florida.
Yes for load-bearing changes. A licensed engineer designs the beam, posts and connections, and most jurisdictions require sealed drawings with the permit.
It varies by city or county, project type and review workload, so we cannot promise a fixed number of weeks.
The engineer decides. Span, load, roof type and available space determine whether LVL, steel or another material is used.
We serve Southwest Florida and the Tampa Bay region from our Clearwater office. Send us your address and we will confirm.
Send us the address and a short description so we can schedule a site visit.
SW Florida Builders GroupFlorida Certified General Contractor CGC1532489
ASasA